COMBINED SHIPPING FOR MULTIPLE ORDERS PLACED ON THE SAME DAY.
FREE Priority Mail (2-3 day arrival) shipping to all United States zipcodes, including Guam and US Virgin Islands.
$14 for the rest of the world.
No matter how many you buy, one flat rate price for shipping!
What is a battery desulfator you ask? It is an electronic device that cleans the internal battery plates to remove the lead sulfate that builds up on poorly maintained batteries. This lead sulfate (that white residue) will form on the batteries internal plates and greatly reduces the capacity of a charge on a battery. By restoring the lead sulfate back into the acid solution you can greatly extend the life of the battery by many years. Our product is designed to be left connected "full-time" to the battery and will provide many years of maintance free operation. This product will work on all types of lead based batteries, including sealed lead acid (SLA), and the more common flooded lead acid (deep cycle or automotive). It is recommended that a small trickle style charger in the 1-2 amp range be used when recovering a battery with heavy deposits. Large high current, bulk rate chargers, will quickly cause heat build up in the battery and could boil the acid causing a very dangerous condition. For large battery systems, like that of a golf cart or solar battery bank, one desulfator is required per battery. This product will desulfate batteries ranging from 1 amp hour to 1000 amp hours. We even include the ring lug terminals preinstalled and ready to use. Our product is 100% made in the USA, yes even the labor. Thank you for taking the time to read about our product. Buy the Best - Be the Best
Battery Desulfator BD-12 series
Proven Circuit Design
Surface Mount Technology PCB
Strong ABS enclosure with mounting tabs
Large Input Voltage Range 4.5 - 16VDC
Low current draw components
100% Made in the USA
1.) The Wizbang desulfator should be installed as close as possible to the battery terminals. (within 14 inches, or 35 cm)
2.) You many trim the wire leads back with wire cutters/strippers to work best for your application. (shorter is better)
3.) Install the Red wire to the positive (+) terminal on your 6, 8 or 12 volt battery.
4.) Install the Black wire to the negative(-) terminal on your 6, 8 or 12 volt battery.
5.) Verify that the green LED is on, you might also be able to hear a “buzzing” noise.
6.) The best results for recovery will occur within the first 4 weeks. If left connected longer, desulfating will continue but at a slower pace.
7.)The Wizbang desulfator has a built in auto ranging feature that will automatically adjust for different battery voltages.
8.) You are done. J Happy desulfating.
NOTE: If you connect the wires incorrectly no damage will be done. Simply reverse the wire leads so that they are correctly installed and the green LED should be lit.
INPUT VOLTAGE 4.5Vdc – 16Vdc
OUTPUT VOLTAGE 60V (pk-pk) inductive (10uS pulse every 1mS approx.)
RATED CURRENT 45mA Average @ nominal 12Vdc input.
FREQUENCY RANGE .8 – 1.2 KHz. Temperature and input voltage dependant
OVERLOAD Internal 4 amp SMT style fuse, fast blow type.
OVER VOLTAGE Some limited protection is provided.
REVERSE POLARITY Fully protected for reverse polarity, No damage will occur
WORKING TEMP. 0C ~ +60C (+32F ~ +140F) (+273K ~ +333K)
WORKING HUMIDITY 20 ~ 90% RH non-condensing
STORAGE TEMP. -20 ~ +85C (-4F ~ +185F) (+253K ~ 358K)
VIBRATION MAX. 10-500HZ, 2G 10min./1cycle, Period for 60min. Along X,Y,Z axis
WITHSTAND VOLTAGE I/P – O/P: 3KVAC
ISOLATION RESISTANCE I/P – O/P: 100m ohms / 500Vdc
MTBF 230.7K hours min. MIL-HDBK-217F (+25C)
DIMENSION 81.30mm(L) x 38.10mm(W) x 25.43mm(H) (3.2”L x 1.5”W x 1.0”H)
The manufacturer reserves the right to change these specifications at any time without notice.